Kit P/N: 51/54-11272 Make: BMW Model: Year: Engine: M5 (E60) 06-08 V10-5.0L M6 (E63/64) 06-08 V10-5.0L T ools Required: 5/16″ nut driver 1/4″ nut driver Flat head screwdriver 10mm socket or extension T20 torx bit T30 torx bit 5mm allen key Note: Filter Cleaning and Re-oiling: When cleaning your aFe filter, be sure to use only aFe’s “Restore Kit” (aFe P/N: 90-50001 blue oil aerosol, or aFe P/N: 90-50501 blue squeeze bottle oil). Filter Replacement: Pro-55R TM PN: 24-90052 (black w/blue media). Pro Dry S TM P/N: 21-90052 (black w/white media) Pro Dry S TM cleaning: see cleaning instruction sheet 06-00074 . or 72-35008 Pro-GUARD 7™ media, (black w/gold media). Pre-filters: 28-10011 yellow, 28-10012 red, For replacement part(s) or “Restore Kit” please call aFe sales/tech support @ 951-493-7100 o28-10013 black, and 28-10014 blue 06-880245 Pg 2 Last update: 05-22008 ™ 1 Clamp, #072 3 Clamp, #060 7 Button head, screws M6 7 Washer, wavy M6 1 Washer, flat M6 1 Screw, hex M6 2 Screws, M4 x .7 x 16 1 3/4″ trim seal @ 13″ L 1 7/16″ trim seal @ 3.5″ L 1 Pre-filter Place washer inlet reservoir onto housing tab. Step 27 Install air filter and tighten using 5/16″ nut driver. Install pre filter. Make sure cap is installed in filter top. Re-connect MAF sensor harness. Step 28 Your installation is now complete. Check both driver and passenger side clamps and components periodically. Thank you for choosing aFe power! Step 29 1 1 2 05-00970 05-00983 Parts list Driver side : 1 Air filter ( Pro-55R™ 24-90052 or Pro Dry S™ 21-90052) 1 Housing 1 Diverter, air filter05-00970 1 Diverter, housing 05-00983 1 Coupler, reducer (4-1/4″ X 3-1/2″) 1 Coupler, straight (3-1/2″ X 2″) 1 Tube, 05-00969 1 Adaptor, air filter 1 Gasket, MAF… Step 15 Attach filter adaptor to housing using 3 button head screws & wavy washers. Tighten using 5mm allen key. Step 20 With couplers and clamps provided, install tube into vehicle. Step 25 Pull out lines on top of air box. Step 16 Attach air diverters to housing using button head and wavy washers. Tighten using 5mm allen key. Install 3/4″ trim seal on housing. Install small 7/16″ trim seal to corner of housing. Note: Failure to install air diverters may result in CEL (Check Engine Light). Step 21 Position tube and tighten all clamps using 5/16″ nut driver. Step 26 Disconnect MAF sensor harness. Loosen clamps with 1/4″ nut driver. Take out plastic intake tube. Step 17 Place housing in vehicle. Attach tab to front radiator support using supplied M6 screw and washer. Step 22 1) Loosen the 2 bolts holding in bottom half of air box. 2) Push back clip on bottom half of airbox, located on bottom ram air unit. Step 18 Re-install nut from step 4 and tighten using 10mm socket or wrench. Step 23 Remove air box from vehicle.Download 2006 2007 2008 BMW M5 and BMW M6 V10-5.0L Intake kit Installation Instructions PDF
Get the file Download here | ALL PDF Manual