This SCHROTH asm harnessbelt is only suitable for adults on
front outboard seating positions.
SCHROTH asm harnessbelts are not intended or suited for
use by children under 12 years of age, or persons who weigh
less than 88 lbs (40 kg) or those who are less than 4'11" tall
(1.50 meters), regardless of age. Such persons will not be
adequately protected by the harness system and may receive
more severe injury than would otherwise be expected.
SCHROTH U.S. model harnessbelts have been tested in
accordance with performance parameters of Federal Motor
Vehicle Safety Standard 209 with the exception of
Paragraph S 4.6 (full scale impact testing as described in
FMVSS 208). FMVSS 209 deals with lap and three point
restraints and does not expressly refer to harness belts.
SCHROTH has nevertheless applied the performance criteria
specified in FMVSS 209 to the system to the extent applicable.
These belts, when properly installed and used according to
applicable instructions can mitigate injury. The ability of any
restraint system to mitigate or prevent injury is directly related
to the type and severity of the accident. SCHROTH asm
harnessbelts have been tested in dynamic sled tests utilizing a
75 kg (165 lbs) Hybrid II anthropometric dummy to simulate
head-on collisions at 50 km/h (31 mph). They also have been
dynamically tested utilizing a 75 kg mass dummy in
accordance with European Safety Standard ECE-R 16.04.
• Always keep this manual in the vehicle so that others can
thoroughly familiarize themselves with the proper use of
the system.
INSTALLATION INSTRUCTIONS
1 General Instructions
Always leave original equipment seat belts in place and
available for use.
We strongly recommend that you leave in place all BMW
factory provided 3-point restraint systems originally supplied for
the front and rear seating positions of your vehicle when you
install the SCHROTH asm harnessbelt. Removal of original
equipment restraint systems may also violate applicable State
or Federal law.
To carry rear seat passengers, you must use your standard 3-
point factory provided front seat belts. To use the factory
installed seat belts after a SCHROTH BMW Rallye 4 belt has
been installed you must first release (un-clip) all four points of
the SCHROTH belt and remove it.
Leaving original equipment restraint systems in place and fully
functional will enable you to choose either the SCHROTH
Rallye 4 OR the vehicle’s standard seat belts when it is
necessary to transport passengers in any of the rear seats or
when either harness belt is not suited for use by the driver or
front seat passenger.
INSTALLATION & OPERATING
INSTRUCTIONS
BMW E36 & E46 3 Series
BMW E39 5 Series
File Type: PDF Download here
Showing posts with label BMW E36. Show all posts
Showing posts with label BMW E36. Show all posts
Wednesday, July 10, 2013
Wednesday, July 13, 2011
Lights Installation guide for BMW E36 & BMW E39 Lights Installation guide
BMW E36 Fitting Instructions. Page 5 of 5. 11, Remove the back cover from the headlamp and remove the side light bulb holder. 12, Wiring the power pack into …BMW E36 & BMW E39 Eclipse Lights Installation guide…
Eclipse Lights – BMW E36 Installation guide www.eclipse-lights.com BMW E36 Fitting Instructions Page 2 of 2 With the headlamps removed from the vehicle :. 1, Use a flat blade screwdriver, remove the 4 metal clips holding the lens assembly and back housing together. 2 clips are on the top and 2 clips on the bottom.
2, Unclip the lens assembly from the rear housing. There are 4 clips to release, 2 on each side of the headlamp. 3, Pull the lens assembly apart from the rear housing and place on a clean surface. Ensure that the headlamp lenses are clean and free of any dirt/dust. Clean them it if necessary ! 5, Carefully place the ring into the lens cavity. Ensure the ring is seated flat against the lens. * It may be necessary to bend the wiring on the end of the ring, If necessary please do so very carefully. 6, Use masking tape to hold the rings in position…
Free Download : Lights Installation guide for BMW E36 & BMW E39 Lights Installation guide
Download BMW E36 & BMW E39 Lights Installation guide.Pdf
File : PDF
Size : kb
The following free ebook for download. We hope this free eBook can help you to fix your faulty devices ...
Repair manual download ...
Find more info about Lights Installation guide for BMW E36 & BMW E39 Lights Installation guide
link downlaod below
Download here
Eclipse Lights – BMW E36 Installation guide www.eclipse-lights.com BMW E36 Fitting Instructions Page 2 of 2 With the headlamps removed from the vehicle :. 1, Use a flat blade screwdriver, remove the 4 metal clips holding the lens assembly and back housing together. 2 clips are on the top and 2 clips on the bottom.
2, Unclip the lens assembly from the rear housing. There are 4 clips to release, 2 on each side of the headlamp. 3, Pull the lens assembly apart from the rear housing and place on a clean surface. Ensure that the headlamp lenses are clean and free of any dirt/dust. Clean them it if necessary ! 5, Carefully place the ring into the lens cavity. Ensure the ring is seated flat against the lens. * It may be necessary to bend the wiring on the end of the ring, If necessary please do so very carefully. 6, Use masking tape to hold the rings in position…
Download BMW E36 & BMW E39 Lights Installation guide.Pdf
File : PDF
Size : kb
The following free ebook for download. We hope this free eBook can help you to fix your faulty devices ...
Repair manual download ...
Find more info about Lights Installation guide for BMW E36 & BMW E39 Lights Installation guide
link downlaod below
Download here
Subscribe to:
Posts (Atom)